详细解释
榫
1、框架结构两个或两个以上部分的接合处。
例句
我感觉有榫舌和凹槽的木材才是环保的。
I suppose the environmental way would be to use tongue-in-groove lumber.
榫锯是一种特殊的墨线戽。
A mortice gauge is a special type of marking gauge.
木材。组装。多榫接头连接。弯曲试验。
Wood. Assembly. Multiple finger joints. Flexion test.
木材机加工刀具。榫口加工刀具。尺寸。
Mechanical tooling for wood. Cutters for rabbet. Dimensions.
你也可以买现成的圆木榫。
You can also buy readymade dowels from mail-order suppliers.
那木匠用卡钳估量暗榫。
The carpenter gauged the dowel with calipers.
榫舌可设在每块厚板的与凹槽相对的侧面上。
The tongue can be on the opposing side of each plank from the groove.
调来取得了伟大的榫切割技术和带锯相吻合。
Tune in to get a great technique for cutting the tenons and dovetails on the bandsaw.
每块必有两榫相对。帐幕一切的板都要这样做。
With two projections set parallel to each other. Make all teh frames of the tabernacle in this way.
另外我们还买了一架电动榫凿和一个最新式的电钻。
Besides, we bought a power mortise chisel and an electric drill of the latest model as well.
你分组件买这个书橱，再把它们卡榫对准组合在一起。
You buy this bookcase in sections and slot them together.
文中简要介绍了涡轮盘枞树形榫齿精拉刀的设计方法。
This thesis briefly introduces the design methods of the fir-tree tenon tooth accurate broach of turbine disk.
本文研究实木榫建模与数控开榫计算机辅助制造技术。
This paper studies Wood Tenoner Modeling and Computer-aided manufacturing about numerical control tenon process.
一般有三种方法来解决这个问题，圆木榫、饼干榫和木楔。
There are three common solutions to this problem: dowels, joining plates and splines.
先在要对接的边上每隔6 ~8英寸画一个圆榫定位标记。
Start by laying out the dowel locations every 6 in. to 8 in. along the joint.
做好圆榫后，在要对接的两边和榫孔内都涂上薄薄一层胶水。
Once your dowels are cut to size, spread a thin layer of glue in all the dowel holes and along the edges of the mating boards.
大多数榫头除了在长边方向有榫肩，在两个短边方向也有榫肩。
Most tenons also have shoulder cuts on the top and bottom edges.
链式制榫机的链条须设有护罩，在切实可行范围内尽量将铣刀围封。
The chain of a chain mortising machine shall be provided with a guard that shall enclose the cutters so far as practicable .
榫合式防撬门是一种新型的安全防盗门，安全性较以前的有很大提高。
The burglary-proof door with rabbet joint is new and much safer than those before.
衔接技术，例如，人字缝，榫和触点，木制钉了所有已知的和广泛使用。
Techniques such as dovetailing, mitre joints, tenon and mortice , wooden dowels were all known and extensively used.
着种斗拱结构造工精致，不用一根钉子，完全采用榫头，榫槽相互衔接。
The roof structure is supported by a wood en system of brackets are connected by mortise and tendon joints and not a single nail is used for connection.
你还应该用砂纸给每个圆榫的两端倒个角，这样能让圆榫更容易对准榫孔。
You also should slightly bevel both ends of the dowel with a piece of sandpaper. This bevel makes aligning the dowels in their mating holes easier.
他说，估计是雨水渗进了木钉孔里，而正是这些木榫钉使它们结合在一起的。
He said he figured the rainwater had settled in the pinholes, where wooden dowels held the joints together.
如指定使用外螺纹及内螺纹或榫面及槽面法兰，容器设备口法兰端面应为凹槽型。
When male and female (M&F) or tongue and groove (T&G) type flanges are specified, the nozzle flange facing of the vessel shall be of female or groove type.
对铣削加工的榫形作了数学描述，并根据榫形的数学模型生成铣削时的刀具轨迹。
According to forming mathematic model, the tenons were depicted in mathematics, and the cutting tracks were formed.
通过模态实验校验的手段证明用这种方法进行榫接装配系统动力学分析是可行的。
Through modeling experiment , this method is proved to be feasible for analyzing the rabbet assembly structure.
通过模态实验校验的手段证明用这种方法进行榫接装配系统动力学分析是可行的。
Through modeling experiment , this method is proved to be feasible for analyzing the rabbet assembly structure.